Your web browser is out of date.

Update your browser for better security, speed and to get the best experience on this website.

Update your browser

Guest blog: MBR sludge − fouling or clogging?

Shutterstock 1234382428
Blog June 17 Mbr Sludge Fouling Or Clogging Author

Dr Pompilia Buzatu

Dr Pompilia Buzatu, post-doctorate researcher at the Gas Processing Center in the College of Engineering, Qatar University, discusses her research into MBR fouling and clogging

We’ve spent a few months now here at Qatar University looking at clogging in membrane channels, with our single-channel bench-scale plant.

The method we’ve ended up with involves simply taking a few litres of MBR sludge from a nearby MBR (treating industrial effluent) and running tests at relatively high flux and slightly diminished air scour rates. This is less ‘real life’ than the Cranfield University tests on a full-scale immersed hollow fibre module (Buzatu et al, 2012), but the conditions can be controlled more precisely.

Figure 1. (a) The single-channel bench-scale plant. (b) A clogged membrane channel
Figure 1. (a) The single-channel bench-scale plant. (b) A clogged membrane channel
Blog June 17 Mbr Sludge Fouling Or Clogging Fig1Ab

It’s early days yet, but there does seem to be a roughly inverse relationship between fouling and clogging. We spent a long while trying to get a highly fouling industrial sludge to clog the membrane channel, but all we got was fouling. However, once we got hold of a reasonable quality sludge with a relatively high sustainable flux, clogging (or specifically sludging, the filling of the membrane channels with solids sometimes called ‘localised dewatering’) was evident.

Adapted from: Credit: Judd Water & Wastewater Consultants
Adapted from:
Blog June 17 Mbr Sludge Fouling Or Clogging Fig 2Credit: Judd Water & Wastewater Consultants

And it’s pretty nasty stuff: a semi-solid cake which is difficult to dislodge without removing the membrane. It's also quite stable in water when exposed to linear air flows of around 0.09 m/s, this velocity being comparable to those used at full-scale (Böhm and Kraume, 2015; Yang et al, 2017). In the video it can be seen towards the end of the clip that even if the sludge solids become dislodged from the membrane surface they are not necessarily cleared from the channel by the air flow.

Membrane bioreactor sludge fouling or clogging

So, it could be that good quality sludge is still liable to cause sludging even if it doesn’t foul the membrane. Of course, there are many, many studies of membrane fouling, something which Simon (Judd) has stated ad nauseum, but it’s never been clear as to whether sludging and fouling are related. If they’re not, and thus all those lovely EPS (extracellular polymeric substances) which fill the literature aren’t relevant to sludging, then maybe it’s necessary to find some other way of characterising the sludge to provide an indication of sludging/clogging.

The very simple and practical test developed by Marcin Stefanski (Stefanski et al, 2011) certainly gives an indication of ragging propensity. But ‘ragging’, the formation of long rags (or braids) of agglomerated cotton wool or other textiles, is not necessarily the same as clogging. Actually, we still don’t know what causes clogging since there have been so few studies of it. Perhaps it actually does relate to EPS: I’m sure there are a lot of researchers who would be relieved if this were to be the case.

Anyway, back to the day job...


Böhm, L., and Kraume, M. (2015). Fluid dynamics of bubble swarms rising in newtonian and non-newtonian liquids in flat sheet membrane systems. J. Membr. Sci., 475, 533−544.

Buzatu, P., Zsirai, T., Aerts, P. and Judd, S.J. (2012). Physical and chemical cleaning efficacy of a submerged hollow fibre MBR, J. Membrane Sci. 421−422 342−348.

Judd, S.J. (2014). Industrial MBRs, Judd & Judd.

Stefanski, M., Kennedy, S., and Judd, S.J. (2011). The determination and origin of fibre clogging in membrane bioreactors, J. Membrane Sci., 375 (2011) 198−203.

Yang, M., Yu, D., Liu, M., Zheng, L., Zheng, X., Wei, Y., Wang, F, and Fan, Y. (2017). Optimization of MBR hydrodynamics for cake layer fouling control through CFD simulation and RSM design. Biores. Technol. 227 102−111.

About this page

'Guest blog: MBR sludge − fouling or clogging?' was written by Dr Pompilia Buzatu

This page was last updated on 04 May 2022


Information on this page may have been supplied by third parties. You are reminded to contact any third parties to confirm information is accurate, up to date and complete before acting upon it. accepts no liability for information provided by third parties, actions taken on the basis of this information or information held on third-party websites.