Your web browser is out of date.

Update your browser for better security, speed and to get the best experience on this website.

Update your browser
Advert

Aeration costs in MBRs

Created
Updated
Image of bubbles in water. The water is mostly blue with tinges of green to the bottom right.

Membrane and process aeration

Energy demand is a key cost factor when considering MBR technology. The main contributors to energy costs are sludge transfer, permeate production and, most significantly, aeration.

Membrane aeration is normally achieved via coarse bubble aerators positioned beneath the membrane units.

Aeration demanded for membrane scouring can be normalised to produce the specific aeration demand (SAD). Normalisation can be either against the membrane area (SADm, taking units of Nm3/(m2.h)) or against the permeate volume (SADp, Nm3/m3).

SADp is then directly proportional to the specific energy demanded for membrane air scouring, or SEDAm, since all other components of air pumping (namely the blower efficiency, aerator depth, inlet air pressure, aerator type, and ratio of air and water enthalpies) are constant for a specific installation. SADp is the ratio of SADm to the flux in consistent units, i.e. in m/h; energy efficiency is improved both by increasing the sustainable flux and decreasing the membrane air scour rate required to sustain this flux.

Aeration for biological treatment, often referred to as the ‘process aeration’, is dependent primarily on the inlet and outlet biodegradable organic carbon and Kjeldahl nitrogen levels, Kjeldahl nitrogen (KN) being biologically oxidisable nitrogen. The absolute difference between inlet and outlet defines the load, and thus the oxygen demanded by this load to convert organic carbon to carbon dioxide and KN to nitrate (nitrification).

Need training? Contact Judd Water & Wastewater Consultants for bespoke training in potable and wastewater treatment technology - remotely or we come to you | sponsored
Fig. 1. α-factor vs. MLSS, according to various authors
Fig. 1. α-factor vs. MLSS, according to various authors
A line graph to demonstrate α-factor vs. MLSS, according to various authors.

The actual aeration rate demanded to deliver a specific dissolved oxygen (DO) concentration is dependent on key design parameters, such as the aerator type and the depth to which it is submerged in the tank, and the residual DO and sludge solids concentration. The efficiency of transfer of oxygen from air into the sludge is defined by the alpha factor (α), which is simply the ratio of the mass transfer coefficient of water to that of the sludge. α decreases with solids concentration according to trends which appear to vary widely between different studies but which generally follow a pseudo-exponential relationship.

So, according some relationships, the aeration rate required to maintain a specified DO residual may double between a process sludge solids concentration of 7 and 12 g/L.

References

Cornel, P., Wagner, M. & Krause, S. (2003). Investigation of oxygen transfer rates in full scale membrane bioreactors. Water Science and Technology 47 (11), 313−319.

Germain, E., Nelles, F., Drews, A., Pearce, P.,Kraume, M., Reid, E., Judd, S. J. & Stephenson, T. (2007). Biomass effects on oxygen transfer in membrane bioreactors. Water Research 41 (5), 1038−1044.

Henkel, J., Lemac, M., Wagner, M. & Cornel, P. (2009). Oxygen transfer in membrane bioreactors treating synthetic greywater. Water Research 43 (6), 1711−1719.

Krampe, J. and Krauth, K. (2003). Oxygen transfer into activated sludge with high MLSS concentrations. Water Sci. Technol., 47, 297−303.

Müller, E.B., Stouthamer, A.H., Vanverseveld, H.W. and Eikelboom, D.H. (1995). Aerobic domestic waste-water treatment in a pilot-plant with complete sludge retention by cross-flow filtration. Water Res., 29, 1179−1189.

Rosenberger, S. (2003) Characterization of Activated Sludge from Membrane Bioreactors Treating Wastewater ‘Charakterisierung von belebtem Schlamm in Membranbelebungsreaktoren zur Abwasserreinigung’. VDI Verlag GmbH, Düsseldorf.

About this page

'Aeration costs in MBRs' was written by Simon Judd

This page was last updated on 23 August 2021

Disclaimer

Information on this page may have been supplied by third parties. You are reminded to contact any third parties to confirm information is accurate, up to date and complete before acting upon it. TheMBRSite.com accepts no liability for information provided by third parties, actions taken on the basis of this information or information held on third-party websites.

© Text copyright Judd & Judd Ltd unless otherwise indicated on this page

You might also be interested in …

You are in:

Share or bookmark this page